-
EGR BLANKING & SILICONE HOSE KIT Code: DA1108TDI Kit contains - blue silicone hoses, EGR kit & Jubilee clips Defender - 300Tdi engine Discovery 1 - 300Tdi engine Range Rover Classic - 300Tdi engine Better fuel economy... Improved performance... A Britpart EGR (exhaust gas recirculation) blanking kit enables you to remove the original mechanical EGR from the vehicle resulting in better fuel economy and improved performance. Britpart silicone hoses are quality intercooler hoses designed to operate at a higher temperature then the original hoses. Fits with both standard and performance intercoolers. Will not rot or perish like standard rubber hoses. -
BRITPART SERVICE KIT Code: DA6003 Defender - 300Tdi Servicing a Land Rover just got a whole lot easier with Britpart! Ever started servicing a Land Rover and then suddenly realised you haven't ordered a filter for forgot the sump plug washers? Well now thanks to Britpart with one simple part number you can order your Land Rover kit safe in the knowledge that all the parts you need will be there for you to complete the job. No more half-finished services! The Britpart service kits contain quality products which are - > Manufactured to O.E. specification > Competitively priced > Available from stock Kit contains - 1 x ERR3340 Oil filter 1 x ESR2623 Air filter 1 x AEU2147L Fuel filter 1 x UAM2857L Sump plug washer 1 x ALU1403L Sump plug washer -
STARTER DIESEL 2.5 Code: RTC5249N -
SEAL KIT DOOR HANDLE Code: STC617 -
SEAL-OIL-CRANKS Code: LUF100420LR -
SHAFT-REAR AXLE Code: TOB500020 -
SHAFT-REAR AXLE Code: TOB500030 -
OLD MAN EMU HANDLING KIT Code: DA2861 Medium-duty full kit Defender 110 > Fully integrated Old Man Emu handling kits for all ride types > Designed and tested by a team of specialist engineers in Australia > Superior performance across all terrain > Dramatically improved high and low speed control for increased comfort Any suspension modification should have a full wheel alignment to ensure the vehicle is set Note - Kit lifts Defender from standard height to between 1" & 2" dependent on kit fitted (winch etc) -
OLD MAN EMU HANDLING KIT Code: DA1740 Medium-duty full kit Defender 90 > Fully integrated Old Man Emu handling kits for all ride types > Designed and tested by a team of specialist engineers in Australia > Superior performance across all terrain > Dramatically improved high and low speed control for increased comfort Any suspension modification should have a full wheel alignment to ensure the vehicle is set Note - Kit lifts Defender from standard height to between 1" & 2" dependent on kit fitted (winch etc) -
OLD MAN EMU COIL SPRINGS D110 Code: DA6841 Rear Lift - Up to 40mm Defender 110 - Station Wagon Spring rate - 175/200lbf/in / 31/35N/mm Free height - 440mm Defender - 110. Load - Station Wagon > Manufactured from state of the art micro-alloyed spring steel for superior strength and durability. > Double scragged before and after shot peening to reduce spring stress and enhance spring life. > Exceptional resistance to sagging and corrosion. > Springs are designed for each vehicle to match the spring to the specific applications. > Springs formed on computer controlled, precision mandrels to ensure manufacturing consistency. > Spring end configurations designed to exact specifications, guaranteeing perfect fitment to your vehicle. > Durable, hard wearing black powder coat. > Designed and manufactured in Australia. Notes Caution: Due to altered gearbox mounts on models after 1998 any lift above. OE ride height may cause front driveline vibration that can only be rectified by fitment of a front double cardan propshaft. On Vehicles fitted with an OE inner helper coil such as fitted to some 110 and 130 models. The inner coil must be retained with OME coils. -
OLD MAN EMU COIL SPRINGS Code: DA8923 Rear Lift - Up to 55mm Defender - 110 Defender - 130 Spring rate - 420lbf/in / 74N/mm Free height - 435mm Defender - 110. Load - 500kgs Defender - 130. Load - 400kgs > Manufactured from state of the art micro-alloyed spring steel for superior strength and durability. > Double scragged before and after shot peening to reduce spring stress and enhance spring life. > Exceptional resistance to sagging and corrosion. > Springs are designed for each vehicle to match the spring to the specific applications. > Springs formed on computer controlled, precision mandrels to ensure manufacturing consistency. > Spring end configurations designed to exact specifications, guaranteeing perfect fitment to your vehicle. > Durable, hard wearing black powder coat. > Designed and manufactured in Australia. Notes Caution: Due to altered gearbox mounts on models after 1998 any lift above. OE ride height may cause front driveline vibration that can only be rectified by fitment of a front double cardan propshaft. On Vehicles fitted with an OE inner helper coil such as fitted to some 110 and 130 models. The inner coil must be retained with OME coils.
-
OLD MAN EMU COIL SPRINGS Code: DA8922 Rear Lift - Up to 50mm Defender - 110 Defender - 130 Spring rate - 300lbf/in / 52N/mm Free height - 435mm Defender - 110. Load - 300kgs Defender - 130. Load - light load > Manufactured from state of the art micro-alloyed spring steel for superior strength and durability. > Double scragged before and after shot peening to reduce spring stress and enhance spring life. > Exceptional resistance to sagging and corrosion. > Springs are designed for each vehicle to match the spring to the specific applications. > Springs formed on computer controlled, precision mandrels to ensure manufacturing consistency. > Spring end configurations designed to exact specifications, guaranteeing perfect fitment to your vehicle. > Durable, hard wearing black powder coat. > Designed and manufactured in Australia. Notes Caution - Due to altered gearbox mounts on models after 1998 any lift above. OE ride height may cause front driveline vibration that can only be rectified by fitment of a front double cardan propshaft. On Vehicles fitted with an OE inner helper coil such as fitted to some 110 and 130 models. The inner coil must be retained with OME coils. Important DA8922 has reduced spring rate from OE to provide improved ride quality for light loads -
OLD MAN EMU COIL SPRINGS Code: DA8910 Front Lift - Up to 40mm Defender - 90, 110 & 130 - diesel Defender - 90, 110 - petrol Discovery 1 - diesel Range Rover Classic - diesel Spring rate - 225lbf/in / 39N/mm Free height - 390mm Defender - 90, 110 & 130 - diesel. Load - 50kgs Defender - 90, 110 - petrol. Load - 51 - 110kgs Discovery 1 - diesel. Load 50kgs Range Rover Classic - diesel. Load - 50kgs > Manufactured from state of the art micro-alloyed spring steel for superior strength and durability. > Double scragged before and after shot peening to reduce spring stress and enhance spring life. > Exceptional resistance to sagging and corrosion. > Springs are designed for each vehicle to match the spring to the specific applications. > Springs formed on computer controlled, precision mandrels to ensure manufacturing consistency. > Spring end configurations designed to exact specifications, guaranteeing perfect fitment to your vehicle. > Durable, hard wearing black powder coat. > Designed and manufactured in Australia. Notes Caution: Due to altered gearbox mounts on models after 1998 any lift above. OE ride height may cause front driveline vibration that can only be rectified by fitment of a front double cardan propshaft. On Vehicles fitted with an OE inner helper coil such as fitted to some 110 and 130 models. The inner coil must be retained with OME coils.
-
OLD MAN EMU COIL SPRINGS Code: DA8924 Front Lift - Up to 40mm Defender - 90 - diesel Discovery 1 Range Rover Classic Spring rate - 285lbf/in / 50N/mm Free height - 385mm Load - 51 - 110kgs > Manufactured from state of the art micro-alloyed spring steel for superior strength and durability. > Double scragged before and after shot peening to reduce spring stress and enhance spring life. > Exceptional resistance to sagging and corrosion. > Springs are designed for each vehicle to match the spring to the specific applications. > Springs formed on computer controlled, precision mandrels to ensure manufacturing consistency. > Spring end configurations designed to exact specifications, guaranteeing perfect fitment to your vehicle. > Durable, hard wearing black powder coat. > Designed and manufactured in Australia. Notes Caution: Due to altered gearbox mounts on models after 1998 any lift above. OE ride height may cause front driveline vibration that can only be rectified by fitment of a front double cardan propshaft. On Vehicles fitted with an OE inner helper coil such as fitted to some 110 and 130 models. The inner coil must be retained with OME coils.
-
OLD MAN EMU SHOCK ABSORBER Code: DA8913 REAR PAIR Defender - 90 & 110 - heavy-duty Defender - 130 Discovery 1 - heavy-duty Range Rover Classic - heavy-duty Open length - 560mm Closed length - 346mm Nitrocharger Sport shock absorbers introduces advanced dual-stack deflective disc technology that continuously adapts to the terrain, offering rapid response improvements to ride quality, handling and control. Available in the UK only. Features > Interactive, multi-stacked rebound and compression valving systems ensure optimal damping performance in all conditions. > Vehicle specific fine tuning for superior handling and ride performance. > Piston rod ‘slip ring’ provides more consistent and uniform damping performance. > Triple lipped oil seal with gas retention check valve design virtually eliminates contaminant damage and gas loss. > Impact resistant polymer dirt shield. > Balanced, 35mm Teflon banded piston assembly. > Teflon coated low friction glacier piston rod guide. > 18-25mm induction hardened chrome piston rod. > High quality replacement mounting bushes. > Australian made and engineered. Lower Bush Mount Kit - DA6806 -
OLD MAN EMU SHOCK ABSORBER Code: DA8921 Rear Defender - 90 & 110 Discovery 1 Range Rover Classic Open length - 560mm Closed length - 346mm Nitrocharger Sport shock absorbers introduces advanced dual-stack deflective disc technology that continuously adapts to the terrain, offering rapid response improvements to ride quality, handling and control. Available in the UK only. Features > Interactive, multi-stacked rebound and compression valving systems ensure optimal damping performance in all conditions. > Vehicle specific fine tuning for superior handling and ride performance. > Piston rod ‘slip ring’ provides more consistent and uniform damping performance. > Triple lipped oil seal with gas retention check valve design virtually eliminates contaminant damage and gas loss. > Impact resistant polymer dirt shield. > Balanced, 35mm Telfon banded piston assembly. > Teflon coated low friction glacier piston rod guide. > 18-25mm induction hardened chrome piston rod. > High quality replacement mounting bushes. > Australian made and engineered. Lower Bush Mounting Kit - DA6806
Call Us Today! +6012-220 5085|sales@defenderupgrades.com.my
